Rope Rescue/Equipment/Need/I-beam rigging clamps
From PCSAR
< Rope Rescue | Equipment | Need(Difference between revisions)
(→Need) |
(→Need) |
||
| (3 intermediate revisions not shown.) | |||
| Line 2: | Line 2: | ||
I-beam rigging clamps | I-beam rigging clamps | ||
* for training at Fire Hall | * for training at Fire Hall | ||
| + | *: [[Image:Members:Wuth-imgp1023.jpg|300px]] | ||
** sloped I-beams, flange 4 inches wide | ** sloped I-beams, flange 4 inches wide | ||
*** '''need to determine flange thickness''' | *** '''need to determine flange thickness''' | ||
| Line 11: | Line 12: | ||
== Requirements == | == Requirements == | ||
* adjustable from 4 to 8 inches | * adjustable from 4 to 8 inches | ||
| - | * placeable on sloping I-beam | + | * placeable on sloping I-beam up to 12 degree slope |
** non-rolling | ** non-rolling | ||
* MBS: 40 kN | * MBS: 40 kN | ||
** 2 person load, SSSF, pulley at top | ** 2 person load, SSSF, pulley at top | ||
** = 8993 lbf | ** = 8993 lbf | ||
| - | ** WLL is not the same as MBS. It has a Design Factor (DF) built in for safety. That factor is not documented; OSHA talks about factor 2 in other parts of its standard. But without specification, we assume that the | + | ** WLL is not the same as MBS. It has a Design Factor (DF) built in for safety. That factor is not documented; OSHA talks about factor 2 in other parts of its standard. But without specification, we assume that the MBS is only negligibly greater than the WLL. |
== Product options == | == Product options == | ||
Current revision
Contents |
[edit] Need
I-beam rigging clamps
- for training at Fire Hall
- sloped I-beams, flange 4 inches wide
- need to determine flange thickness
- exterior roof has 12 degrees slope; interior ceiling has 2 angles: the edges are greater, the center less (where we will be working)
- horizontal I-beams, flange approx 7-8 inches wide
- need to determine flange thickness
- more accurately measure flange width
-
[edit] Requirements
- adjustable from 4 to 8 inches
- placeable on sloping I-beam up to 12 degree slope
- non-rolling
- MBS: 40 kN
- 2 person load, SSSF, pulley at top
- = 8993 lbf
- WLL is not the same as MBS. It has a Design Factor (DF) built in for safety. That factor is not documented; OSHA talks about factor 2 in other parts of its standard. But without specification, we assume that the MBS is only negligibly greater than the WLL.
[edit] Product options
[edit] Potentially suitable
- General Clamp Industries
- http://www.superclamp.com/
- GCI Swivel-Jaw Adjustable Girder Clamp
- For use at up to 15° from horizontal
- website says: from vertical
- Approved for Personnel tie-off use*
- picture
- http://www.superclamp.com/default.asp?ID=13
- 3.5" - 12" flange
- models S6 and S6A
- WLL: 11,200 lb
- model S11
- WLL: 22,400 lb
- models S6 and S6A
- For use at up to 15° from horizontal
- GCI Fixed-Jaw Adjustable Girder Clamp
- For use at up to 15° from horizontal
- website says: from vertical
- Approved for Personnel tie-off use*
- picture
- http://www.superclamp.com/default.asp?ID=12
- model SX3
- WLL: 11,200 lb
- 3" - 7.5" flange
- might not fit larger I-beam
- For use at up to 15° from horizontal
- Tractel
- http://www.tractel.com/us/home.php
- Corso Beam Clamp
- http://www.tractel.com/us/series.php?id_serie=73
- http://www.tractel.com/files/126564497571957.pdf
- http://www.ahsrescue.com/p-1223-pmi-tractel-beam-clamp.aspx
- http://shop.pmirope.com/technical-hardware/index.aspx?pageID=43&productID=333&productMasterID=333
- http://www.torqhoist.com/show_unique_product.php?product_id=12
- This anchorage is designed to fit I-beams from 3 to 8.25 inches. Simple installation, removable. Meets ANSI, CSA, and OSHA 5400lbs (24kN) anchorage requirements.
- Model Lt 5B
- 5 ton = 10,000 lb
- flange width: 2.9" - 8.7"
- Model Lt 10B
- 10 ton = 20,000 lb
- flange width: 3.5" - 8.7"
- Reliance Fall Protection
- http://www.relsafe.com/
- 3093 HLL Anchor Clamp
- MBS 14,500 lb
- flange width: 4" - 16-5/8"
- horizontal or vertical I-beam
- http://www.relsafe.com/ProductDetails.aspx?guid=e8b2c0bf-5765-42c8-b21b-acf04fc19ae5&pid=561&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d2
[edit] suitability uncertain
Welded ring
[edit] Not suitable
- rigging chains
- require horizontal beam
- http://www.polarfocus.com/view.php?RCS
- All Material Handling (AMH)
- http://www.allmaterialhandling.com/aspnet/Default.aspx
- http://www.allmaterialhandling.com/aspnet/beamclamps.aspx
- http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps
- not rated for live load
- see pictures
- http://www.stageriggingonline.com/beamclamps.html
- http://www.polarfocus.com/view.php?RBC
- level beams only
- FallTech
- http://www.falltech.com/
- http://www.falltech.com/subCat.asp?subCatID=36
- FallTech 7489 Vertical Beam Clamp
- Fits Beams from 2-1/2" - 12" Wide and up to 1-1/2" Flange Thickness.
- Ideal for Vertical or Horizontal I-Beam Structures.
- Rated at over 5,000 lbs.
- no detailed strength rating
- Meets OSHA and ANSI Requirements.
- http://www.falltech.com/productLS.asp?prodID=265
- http://www.westernsafety.com/falltech/falltech08pg3.html
- FallTech 7411 Ratcheting Beam Clamp
- Fits Beams from 4" - 12" Wide and up to 1" Flange Thickness.
- Ideal for Horizontal I-Beam Structures.
- Rated at over 5,000 lbs .
- Meets the Requirements of OSHA 1926 and ANSI Z359.
- http://www.falltech.com/productLS.asp?prodID=165
- http://www.westernsafety.com/falltech/falltech08pg3.html
- manufacturer unclear on sloped used
- FallTech 7485 Portable Beam Clamp
- Fits Beams from 3-1/2" - 12" Wide and up to 1-1/8" Flange Thickness.
- Rated at over 5,000 lbs.
- Meets the Requirements of OSHA 1926 and ANSI Z359.
- http://www.falltech.com/productLS.asp?prodID=263
- http://www.westernsafety.com/falltech/falltech08pg3.html
- manufacturer unclear on sloped used
- FallTech 7486 Portable Beam Clamp
- Fits Beams from 3-1/2" - 18" Wide and up to 1-1/8" Flange Thickness.
- Ideal for Horizontal I-Beam Structures.
- Rated at over 5,000 lbs.
- Meets OSHA and ANSI Requirements.
- http://www.falltech.com/productLS.asp?prodID=264
- http://www.westernsafety.com/falltech/falltech08pg3.html
- manufacturer unclear on sloped used
- FallTech 7487 Stationary Beam Clamp
- Fits Beams from 4" -12" Wide and up to 1-1/8" Flange Thickness.
- Ideal for Horizontal I-Beam Structures.
- Rated at over 5,000 lbs.
- Meets the Requirements of OSHA 1926 and ANSI Z359.
- http://www.falltech.com/productLS.asp?prodID=266
- http://www.westernsafety.com/falltech/falltech08pg3.html
- manufacturer unclear on sloped used
- FallTech 7488
- General Clamp Industries
- GCI Universal Superclamp
- min flange size: 6 inch
- Can be Loaded at Any Angle
- This model is designed to be used at full rated capacity at angles up to 90° in a 360° radius.
- Approved for Personnel tie-off use*
- picture
- http://www.superclamp.com/default.asp?ID=10
- http://www.lamcoinc.com/beamclamp.html
- GCI Universal Superclamp
- Reliance Fall Protection
- http://www.relsafe.com/
- 3089 Adjustable Width Beam Anchor
- 3096 Adjustable Width Sliding Beam Anchor
- http://www.relsafe.com/ProductDetails.aspx?guid=ac7bd5ec-4efd-4d1f-809b-040b9862f8fc&pid=881&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0
- flange width: 3.75" - 12.25"
- but manual says: 5" - 15"
- maximum load: 5000lb
- 3098 Adjustable Width Beam Anchor
- 2 fall arrest links
- rated for sloped I-beams
- http://www.relsafe.com/ProductDetails.aspx?guid=afa7f5cc-699f-401d-81b3-356d5b4c3a73&pid=908&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0
- wrong manual on web page; cannot determine strength rating
- LockJaw Remote Beam Grip Clamp
- Beam Clamp (unclear manufacturer)
- 3 - 9" flange widths
- WLL, Personal 2,000 lbf.
- WLL, Equipment 4,000 lbf.
- http://www.rescuetech1.com/beamclamp.aspx
