ComputerSystemTask
From PCSAR
(Difference between revisions)
(→Tasks:) |
|||
| Line 2: | Line 2: | ||
SARCAR. | SARCAR. | ||
| - | ==Tasks | + | ==Tasks== |
* Determine requirements for SAR computer (done) | * Determine requirements for SAR computer (done) | ||
| - | * Important uses: photocopying, brifing sheet, maps* What do we need when looking for computer sysem* Mass faxing* Topo map software that Bryan has* propose suitable components, get BoardCommittee approval (done)* buy system (mostly done) | + | * Important uses: photocopying, brifing sheet, maps |
| - | * buy 2-sided print option ([[PhotocopierTask]]): [[BrettWuth]]* install system | + | * What do we need when looking for computer sysem |
| + | * Mass faxing | ||
| + | * Topo map software that Bryan has | ||
| + | * propose suitable components, get BoardCommittee approval (done) | ||
| + | * buy system (mostly done) | ||
| + | * buy 2-sided print option ([[PhotocopierTask]]): [[BrettWuth]] | ||
| + | * install system | ||
* physical housing: MikeStauffer, RussellBruder (done) | * physical housing: MikeStauffer, RussellBruder (done) | ||
| + | |||
requirements | requirements | ||
| - | * able to transport under high vibration (e.g. washboard) without | + | * able to transport under high vibration (e.g. washboard) without damaging delicate scanning mechanism |
| - | damaging delicate scanning mechanism* enough space to be able to completely remove the lid | + | * enough space to be able to completely remove the lid (everything above the glass) in order to position large maps for scanning. Lid removes by lifting 2 tabs when lid is open. |
| - | (everything above the glass) in order to position large maps for | + | * enough space to open lid and to use sheet feeder |
| - | scanning. Lid removes by lifting 2 tabs when lid is open.* enough space to open lid and to use sheet feeder* enough space to print legal size (14 inch) paper without | + | * enough space to print legal size (14 inch) paper without crowding into corridor |
| - | crowding into corridor* enough space to open printer to replace ink cartridges. Printer | + | * enough space to open printer to replace ink cartridges. Printer hinges open in the middle by pulling forward where paper comes out. |
| - | hinges open in the middle by pulling forward where paper comes | + | * glass level with counter top to allow large maps to slide on and off printer |
| - | out.* glass level with counter top to allow large maps to slide on | + | * as much space as possible between the printer and the two walls of the corner so as to allow maps to hang over all four edges when scanning large maps. |
| - | and off printer* as much space as possible between the printer and the two walls | + | * easy to reach access to front panel buttons |
| - | of the corner so as to allow maps to hang over all four edges when | + | * the printer will become 2 inches wider (front to back) at the bottom back when the 2-sided print option is purchased. Because the top back currently overhangs the bottom back, this won't make the printer significantly wider (front to back). |
| - | scanning large maps.* easy to reach access to front panel buttons* the printer will become 2 inches wider (front to back) at the | + | * the power inverter needs to attach somewhere to the wall (as a heat sink) and to 12 V. It will power both the printer and the laptop, which will set on the counter. |
| - | bottom back when the 2-sided print option is purchased. Because the | + | * a cord will run between the laptop and the printer. |
| - | top back currently overhangs the bottom back, this won't make the | + | * install power inverter |
| - | printer significantly wider (front to back).* the power inverter needs to attach somewhere to the wall (as a | + | * cache printer paper at firehall and in SARCAR |
| - | heat sink) and to 12 V. It will power both the printer and the | + | * build pictoral of how to pack, carry, transport, unpack |
| - | laptop, which will set on the counter.* a cord will run between the laptop and the printer.* install power inverter* cache printer paper at firehall and in SARCAR* build pictoral of how to pack, carry, transport, unpack* label | + | * label weight of case and printer |
| - | * consider MemoryMap (demoed by RoyDavidson) | + | * software selection and configuration: [[BrettWuth]] |
| - | run under Linux?* convert to journaling file system (ext3) | + | * Mapping Software |
| - | + | * consider MemoryMap (demoed by RoyDavidson) http://www.memory-map.com/ Will it run under Linux? | |
| + | * convert to journaling file system (ext3) http://www.troubleshooters.com/linux/ext2toext3.htm | ||
| + | |||
| + | * train people to use | ||
| + | |||
| + | Brett Wuth, 2005/02/21 23:28 MST (via web): | ||
| - | |||
Used to be assigned to [[BrettWuth]], but removed due to higher | Used to be assigned to [[BrettWuth]], but removed due to higher | ||
priorities | priorities | ||
Revision as of 10:16, 22 November 2008
Making a working computer, photocopier, printer available to the SARCAR.
Tasks
- Determine requirements for SAR computer (done)
- Important uses: photocopying, brifing sheet, maps
- What do we need when looking for computer sysem
- Mass faxing
- Topo map software that Bryan has
- propose suitable components, get BoardCommittee approval (done)
- buy system (mostly done)
- buy 2-sided print option (PhotocopierTask): BrettWuth
- install system
- physical housing: MikeStauffer, RussellBruder (done)
requirements
- able to transport under high vibration (e.g. washboard) without damaging delicate scanning mechanism
- enough space to be able to completely remove the lid (everything above the glass) in order to position large maps for scanning. Lid removes by lifting 2 tabs when lid is open.
- enough space to open lid and to use sheet feeder
- enough space to print legal size (14 inch) paper without crowding into corridor
- enough space to open printer to replace ink cartridges. Printer hinges open in the middle by pulling forward where paper comes out.
- glass level with counter top to allow large maps to slide on and off printer
- as much space as possible between the printer and the two walls of the corner so as to allow maps to hang over all four edges when scanning large maps.
- easy to reach access to front panel buttons
- the printer will become 2 inches wider (front to back) at the bottom back when the 2-sided print option is purchased. Because the top back currently overhangs the bottom back, this won't make the printer significantly wider (front to back).
- the power inverter needs to attach somewhere to the wall (as a heat sink) and to 12 V. It will power both the printer and the laptop, which will set on the counter.
- a cord will run between the laptop and the printer.
- install power inverter
- cache printer paper at firehall and in SARCAR
- build pictoral of how to pack, carry, transport, unpack
- label weight of case and printer
- software selection and configuration: BrettWuth
- Mapping Software
- consider MemoryMap (demoed by RoyDavidson) http://www.memory-map.com/ Will it run under Linux?
- convert to journaling file system (ext3) http://www.troubleshooters.com/linux/ext2toext3.htm
- train people to use
Brett Wuth, 2005/02/21 23:28 MST (via web):
Used to be assigned to BrettWuth, but removed due to higher priorities
