Editing Rope Rescue/Equipment/Need/I-beam rigging clamps
From PCSAR
Warning: You are not logged in. Your IP address will be recorded in this page's edit history.
The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Current revision | Your text | ||
Line 1: | Line 1: | ||
- | |||
I-beam rigging clamps | I-beam rigging clamps | ||
* for training at Fire Hall | * for training at Fire Hall | ||
- | |||
** sloped I-beams, flange 4 inches wide | ** sloped I-beams, flange 4 inches wide | ||
*** '''need to determine flange thickness''' | *** '''need to determine flange thickness''' | ||
- | *** | + | *** '''determine slope angle''' |
** horizontal I-beams, flange approx 7-8 inches wide | ** horizontal I-beams, flange approx 7-8 inches wide | ||
*** '''need to determine flange thickness''' | *** '''need to determine flange thickness''' | ||
*** '''more accurately measure flange width''' | *** '''more accurately measure flange width''' | ||
+ | * requirements: | ||
+ | ** adjustable from 4 to 8 inches | ||
+ | ** placeable on sloping I-beam | ||
+ | *** non-rolling | ||
+ | ** MBS: 40 kN | ||
+ | *** 2 person load, SSSF, pulley at top | ||
+ | *** = 8993 lbf | ||
+ | *** WLL is not the same as MBS. It has a Design Factor (DF) built in for safety. That factor is not documented; it should be at least 5. But without specification, we assume that the WLL must be at least 40 kN | ||
- | + | possible products: | |
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
* General Clamp Industries | * General Clamp Industries | ||
** http://www.superclamp.com/ | ** http://www.superclamp.com/ | ||
** GCI Swivel-Jaw Adjustable Girder Clamp | ** GCI Swivel-Jaw Adjustable Girder Clamp | ||
- | *** For use at up to 15° | + | *** For use at up to 15° from vertical |
- | + | ||
*** Approved for Personnel tie-off use* | *** Approved for Personnel tie-off use* | ||
*** [http://www.superclamp.com/images/ProductsImages_Swivel.jpg picture] | *** [http://www.superclamp.com/images/ProductsImages_Swivel.jpg picture] | ||
Line 37: | Line 31: | ||
***** WLL: 22,400 lb | ***** WLL: 22,400 lb | ||
** GCI Fixed-Jaw Adjustable Girder Clamp | ** GCI Fixed-Jaw Adjustable Girder Clamp | ||
- | *** For use at up to 15° from | + | *** For use at up to 15° from, vertical |
- | + | ||
*** Approved for Personnel tie-off use* | *** Approved for Personnel tie-off use* | ||
*** [http://www.superclamp.com/images/ProductsImages_Fixed.gif picture] | *** [http://www.superclamp.com/images/ProductsImages_Fixed.gif picture] | ||
Line 53: | Line 46: | ||
*** http://www.tractel.com/us/series.php?id_serie=73 | *** http://www.tractel.com/us/series.php?id_serie=73 | ||
*** http://www.tractel.com/files/126564497571957.pdf | *** http://www.tractel.com/files/126564497571957.pdf | ||
- | *** | + | *** multiple sizes |
- | + | ||
- | + | ||
- | + | ||
*** Model Lt 5B | *** Model Lt 5B | ||
**** 5 ton = 10,000 lb | **** 5 ton = 10,000 lb | ||
- | |||
*** Model Lt 10B | *** Model Lt 10B | ||
**** 10 ton = 20,000 lb | **** 10 ton = 20,000 lb | ||
- | **** | + | *** This anchorage is designed to fit I-beams from 3 to 8.25 inches. Simple installation, removable. Meets ANSI, CSA, and OSHA 5400lbs (24kN) anchorage requirements. |
+ | *** one person rated. | ||
+ | *** http://www.ahsrescue.com/p-1223-pmi-tractel-beam-clamp.aspx | ||
+ | *** http://shop.pmirope.com/technical-hardware/index.aspx?pageID=43&productID=333&productMasterID=333 | ||
+ | *** http://www.torqhoist.com/show_unique_product.php?product_id=12 | ||
+ | |||
+ | |||
+ | * FallTech | ||
+ | ** http://www.falltech.com/ | ||
+ | ** http://www.falltech.com/subCat.asp?subCatID=36 | ||
+ | ** FallTech 7489 Vertical Beam Clamp | ||
+ | *** Fits Beams from 2-1/2" - 12" Wide and up to 1-1/2" Flange Thickness. | ||
+ | *** Ideal for Vertical or Horizontal I-Beam Structures. | ||
+ | *** Rated at over 5,000 lbs. | ||
+ | *** Meets OSHA and ANSI Requirements. | ||
+ | *** http://www.falltech.com/productLS.asp?prodID=265 | ||
+ | *** http://www.westernsafety.com/falltech/falltech08pg3.html | ||
* Reliance Fall Protection | * Reliance Fall Protection | ||
** http://www.relsafe.com/ | ** http://www.relsafe.com/ | ||
+ | ** 3089 Adjustable Width Beam Anchor | ||
+ | *** http://www.relsafe.com/ProductDetails.aspx?guid=e0d92262-7c81-4272-93ab-24e3f4b4414a&pid=907&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0 | ||
+ | ** 3096 Adjustable Width Sliding Beam Anchor | ||
+ | *** http://www.relsafe.com/ProductDetails.aspx?guid=ac7bd5ec-4efd-4d1f-809b-040b9862f8fc&pid=881&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0 | ||
+ | ** 3098 Adjustable Width Beam Anchor | ||
+ | *** 2 fall arrest links | ||
+ | *** rated for sloped I-beams | ||
+ | *** http://www.relsafe.com/ProductDetails.aspx?guid=afa7f5cc-699f-401d-81b3-356d5b4c3a73&pid=908&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0 | ||
** 3093 HLL Anchor Clamp | ** 3093 HLL Anchor Clamp | ||
*** MBS 14,500 lb | *** MBS 14,500 lb | ||
- | *** | + | **** but manual says 6,000 lb |
- | * | + | |
*** http://www.relsafe.com/ProductDetails.aspx?guid=e8b2c0bf-5765-42c8-b21b-acf04fc19ae5&pid=561&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d2 | *** http://www.relsafe.com/ProductDetails.aspx?guid=e8b2c0bf-5765-42c8-b21b-acf04fc19ae5&pid=561&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d2 | ||
+ | ** LockJaw Remote Beam Grip Clamp | ||
+ | *** ''min width 5 inch'' | ||
+ | *** rated 10,000 lb - 2 man load | ||
+ | *** http://www.relsafe.com/ProductDetails.aspx?guid=485b7f80-88b9-46a2-8ae9-d8eeb47cf0f5&pid=555&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0 | ||
+ | *** http://www.gravitec.com/equipment/anchors/reliance-lockjaw-remote-beam-grip-clamp/anc-re-3040-1/ | ||
+ | |||
+ | |||
+ | |||
+ | * Beam Clamp (unclear manufacturer) | ||
+ | ** 3 - 9" flange widths | ||
+ | ** WLL, Personal 2,000 lbf. | ||
+ | ** http://www.rescuetech1.com/beamclamp.aspx | ||
+ | |||
- | + | suitability uncertain: | |
Welded ring | Welded ring | ||
Line 79: | Line 104: | ||
- | + | Not suitable: | |
- | * rigging chains | + | * rigging chains (require horizontal beam) |
- | + | ||
** http://www.polarfocus.com/view.php?RCS | ** http://www.polarfocus.com/view.php?RCS | ||
+ | * http://www.polarfocus.com/view.php?RBC | ||
+ | ** "level beams only" | ||
* All Material Handling (AMH) | * All Material Handling (AMH) | ||
Line 90: | Line 116: | ||
** http://www.allmaterialhandling.com/aspnet/beamclamps.aspx | ** http://www.allmaterialhandling.com/aspnet/beamclamps.aspx | ||
** http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps | ** http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps | ||
- | ** | + | ** not rated for live load see [http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps pictures] |
- | + | ||
** http://www.stageriggingonline.com/beamclamps.html | ** http://www.stageriggingonline.com/beamclamps.html | ||
- | |||
- | |||
* FallTech | * FallTech | ||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
** FallTech 7411 Ratcheting Beam Clamp | ** FallTech 7411 Ratcheting Beam Clamp | ||
*** Fits Beams from 4" - 12" Wide and up to 1" Flange Thickness. | *** Fits Beams from 4" - 12" Wide and up to 1" Flange Thickness. | ||
Line 146: | Line 159: | ||
* General Clamp Industries | * General Clamp Industries | ||
** GCI Universal Superclamp | ** GCI Universal Superclamp | ||
- | *** ''min flange size: 6 inch'' | + | *** '''min flange size: 6 inch''' |
*** Can be Loaded at Any Angle | *** Can be Loaded at Any Angle | ||
**** This model is designed to be used at full rated capacity at angles up to 90° in a 360° radius. | **** This model is designed to be used at full rated capacity at angles up to 90° in a 360° radius. | ||
Line 153: | Line 166: | ||
*** http://www.superclamp.com/default.asp?ID=10 | *** http://www.superclamp.com/default.asp?ID=10 | ||
*** http://www.lamcoinc.com/beamclamp.html | *** http://www.lamcoinc.com/beamclamp.html | ||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- | |||
- |