Editing Rope Rescue/Equipment/Need/I-beam rigging clamps

From PCSAR

Warning: You are not logged in. Your IP address will be recorded in this page's edit history.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.

== Need ==
I-beam rigging clamps
* for training at Fire Hall
** sloped I-beams, flange 4 inches wide
*** '''need to determine flange thickness'''
*** '''determine slope angle'''
** horizontal I-beams, flange approx 7-8 inches wide
*** '''need to determine flange thickness'''
*** '''more accurately measure flange width'''
== Requirements ==
* adjustable from 4 to 8 inches
* placeable on sloping I-beam
** non-rolling
* MBS: 40 kN
** 2 person load, SSSF, pulley at top
** = 8993 lbf
** WLL is not the same as MBS.  It has a Design Factor (DF) built in for safety.  That factor is not documented; OSHA talks about factor 2 in other parts of its standard.  But without specification, we assume that the WLL is only negligibly less than MBS.

== Product options ==

=== Potentially suitable ===

* General Clamp Industries
** http://www.superclamp.com/
** GCI Swivel-Jaw Adjustable Girder Clamp
*** For use at up to 15° from horizontal
**** ''website says: from vertical''
*** Approved for Personnel tie-off use*
*** [http://www.superclamp.com/images/ProductsImages_Swivel.jpg picture]
*** http://www.superclamp.com/default.asp?ID=13
*** 3.5" - 12" flange
**** models S6 and S6A
***** WLL: 11,200 lb
**** model S11
***** WLL: 22,400 lb
** GCI Fixed-Jaw Adjustable Girder Clamp
*** For use at up to 15° from horizontal
**** ''website says: from vertical''
*** Approved for Personnel tie-off use*
*** [http://www.superclamp.com/images/ProductsImages_Fixed.gif picture]
*** http://www.superclamp.com/default.asp?ID=12
*** model SX3
**** WLL: 11,200 lb
**** 3" - 7.5" flange
***** ''might not fit larger I-beam''

* Tractel
** http://www.tractel.com/us/home.php
** Corso Beam Clamp
*** http://www.tractel.com/us/series.php?id_serie=73
*** http://www.tractel.com/files/126564497571957.pdf
*** http://www.ahsrescue.com/p-1223-pmi-tractel-beam-clamp.aspx
*** http://shop.pmirope.com/technical-hardware/index.aspx?pageID=43&productID=333&productMasterID=333
*** http://www.torqhoist.com/show_unique_product.php?product_id=12
*** This anchorage is designed to fit I-beams from 3 to 8.25 inches. Simple installation, removable. Meets ANSI, CSA, and OSHA 5400lbs (24kN) anchorage requirements.
*** Model Lt 5B
**** 5 ton = 10,000 lb
**** flange width: 2.9" - 8.7"
*** Model Lt 10B
**** 10 ton = 20,000 lb
**** flange width: 3.5" - 8.7"

* Reliance Fall Protection
** http://www.relsafe.com/
** 3093  HLL Anchor Clamp
*** MBS 14,500 lb
*** flange width: 4" - 16-5/8"
*** horizontal or vertical I-beam
*** http://www.relsafe.com/ProductDetails.aspx?guid=e8b2c0bf-5765-42c8-b21b-acf04fc19ae5&pid=561&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d2

=== suitability uncertain ===

Welded ring
* http://www.relsafe.com/ProductDetails.aspx?guid=11c43404-7da7-405e-a5bd-19f5737d7ccf&pid=884&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d5

=== Not suitable ===

* rigging chains (require horizontal beam)
** http://www.polarfocus.com/view.php?RCS

* http://www.polarfocus.com/view.php?RBC
** "level beams only"

* All Material Handling (AMH)
** http://www.allmaterialhandling.com/aspnet/Default.aspx
** http://www.allmaterialhandling.com/aspnet/beamclamps.aspx
** http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps
** not rated for live load see [http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps pictures]
** http://www.stageriggingonline.com/beamclamps.html

* FallTech
** http://www.falltech.com/
** http://www.falltech.com/subCat.asp?subCatID=36
** FallTech 7489 Vertical Beam Clamp
*** Fits Beams from 2-1/2" - 12" Wide and up to 1-1/2" Flange Thickness.
*** Ideal for Vertical or Horizontal I-Beam Structures.
*** Rated at over 5,000 lbs.
*** ''no detailed strength rating''
*** Meets OSHA and ANSI Requirements.
*** http://www.falltech.com/productLS.asp?prodID=265
*** http://www.westernsafety.com/falltech/falltech08pg3.html
** FallTech 7411 Ratcheting Beam Clamp 
*** Fits Beams from 4" - 12" Wide and up to 1" Flange Thickness.
*** Ideal for Horizontal I-Beam Structures.
*** Rated at over 5,000 lbs .
*** Meets the Requirements of OSHA 1926 and ANSI Z359.
*** http://www.falltech.com/productLS.asp?prodID=165
*** http://www.westernsafety.com/falltech/falltech08pg3.html
*** ''manufacturer unclear on sloped used''
** FallTech 7485 Portable Beam Clamp
*** Fits Beams from 3-1/2" - 12" Wide and up to 1-1/8" Flange Thickness.
*** Rated at over 5,000 lbs.
*** Meets the Requirements of OSHA 1926 and ANSI Z359.
*** http://www.falltech.com/productLS.asp?prodID=263
*** http://www.westernsafety.com/falltech/falltech08pg3.html
*** ''manufacturer unclear on sloped used''
** FallTech 7486 Portable Beam Clamp
*** Fits Beams from 3-1/2" - 18" Wide and up to 1-1/8" Flange Thickness.
*** Ideal for Horizontal I-Beam Structures.
*** Rated at over 5,000 lbs.
*** Meets OSHA and ANSI Requirements.
*** http://www.falltech.com/productLS.asp?prodID=264
*** http://www.westernsafety.com/falltech/falltech08pg3.html
*** ''manufacturer unclear on sloped used''
** FallTech 7487 Stationary Beam Clamp
*** Fits Beams from 4" -12" Wide and up to 1-1/8" Flange Thickness.
*** Ideal for Horizontal I-Beam Structures.
*** Rated at over 5,000 lbs.
*** Meets the Requirements of OSHA 1926 and ANSI Z359.
*** http://www.falltech.com/productLS.asp?prodID=266
*** http://www.westernsafety.com/falltech/falltech08pg3.html
*** ''manufacturer unclear on sloped used''
** FallTech 7488
*** http://www.falltech.com/productLS.asp?prodID=267
*** ''wrong size''

* General Clamp Industries
** GCI Universal Superclamp
*** ''min flange size: 6 inch''
*** Can be Loaded at Any Angle
**** This model is designed to be used at full rated capacity at angles up to 90° in a 360° radius.
*** Approved for Personnel tie-off use*
*** [http://www.superclamp.com/images/ProductsImages_Universal.jpg picture]
*** http://www.superclamp.com/default.asp?ID=10
*** http://www.lamcoinc.com/beamclamp.html

* Reliance Fall Protection
** http://www.relsafe.com/
** 3089 Adjustable Width Beam Anchor
*** http://www.relsafe.com/ProductDetails.aspx?guid=e0d92262-7c81-4272-93ab-24e3f4b4414a&pid=907&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0
*** ''MBS/WLL not specified''
** 3096 Adjustable Width Sliding Beam Anchor
*** http://www.relsafe.com/ProductDetails.aspx?guid=ac7bd5ec-4efd-4d1f-809b-040b9862f8fc&pid=881&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0
*** flange width: 3.75" - 12.25"
**** ''but manual says: 5" - 15"''
*** ''maximum load: 5000lb''
** 3098 Adjustable Width Beam Anchor
*** 2 fall arrest links
*** rated for sloped I-beams
*** http://www.relsafe.com/ProductDetails.aspx?guid=afa7f5cc-699f-401d-81b3-356d5b4c3a73&pid=908&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0
**** '''wrong manual on web page; cannot determine strength rating'''
** LockJaw Remote Beam Grip Clamp
*** ''min width 5 inch''
*** rated 10,000 lb - 2 man load
*** http://www.relsafe.com/ProductDetails.aspx?guid=485b7f80-88b9-46a2-8ae9-d8eeb47cf0f5&pid=555&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0
*** http://www.gravitec.com/equipment/anchors/reliance-lockjaw-remote-beam-grip-clamp/anc-re-3040-1/

* Beam Clamp (unclear manufacturer)
** 3 - 9" flange widths
** WLL, Personal   2,000 lbf.
** WLL, Equipment  4,000 lbf.
** http://www.rescuetech1.com/beamclamp.aspx

Please note that all contributions to PCSAR are considered to be released under the Attribution-Share Alike 3.0 Unported (see PCSAR:Copyrights for details). If you don't want your writing to be edited mercilessly and redistributed at will, then don't submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. DO NOT SUBMIT COPYRIGHTED WORK WITHOUT PERMISSION!

Summary:

Cancel | Editing help (opens in new window)

Retrieved from "http://pcsar.dyndns.org:8080/mediawiki/index.php/Rope_Rescue/Equipment/Need/I-beam_rigging_clamps"

Editing Rope Rescue/Equipment/Need/I-beam rigging clamps

From PCSAR

Views

Personal tools

Navigation

Search

Toolbox

@@ Line 2: / Line 2: @@
 I-beam rigging clamps
 * for training at Fire Hall
-*: [[Image:Members:Wuth-imgp1023.jpg|300px]]
 ** sloped I-beams, flange 4 inches wide
 *** '''need to determine flange thickness'''
-*** exterior roof has 12 degrees slope; interior ceiling has 2 angles: the edges are greater, the center less (where we will be working)
+*** '''determine slope angle'''
 ** horizontal I-beams, flange approx 7-8 inches wide
 *** '''need to determine flange thickness'''
 *** '''more accurately measure flange width'''
 == Requirements ==
 * adjustable from 4 to 8 inches
-* placeable on sloping I-beam up to 12 degree slope
+* placeable on sloping I-beam
 ** non-rolling
 * MBS: 40 kN
 ** 2 person load, SSSF, pulley at top
 ** = 8993 lbf
-** WLL is not the same as MBS.  It has a Design Factor (DF) built in for safety.  That factor is not documented; OSHA talks about factor 2 in other parts of its standard.  But without specification, we assume that the MBS is only negligibly greater than the WLL.
+** WLL is not the same as MBS.  It has a Design Factor (DF) built in for safety.  That factor is not documented; OSHA talks about factor 2 in other parts of its standard.  But without specification, we assume that the WLL is only negligibly less than MBS.
 == Product options ==
@@ Line 81: / Line 79: @@
 === Not suitable ===
-* rigging chains
+* rigging chains (require horizontal beam)
-** ''require horizontal beam''
 ** http://www.polarfocus.com/view.php?RCS
+* http://www.polarfocus.com/view.php?RBC
+** "level beams only"
 * All Material Handling (AMH)
@@ Line 90: / Line 89: @@
 ** http://www.allmaterialhandling.com/aspnet/beamclamps.aspx
 ** http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps
-** ''not rated for live load''
+** not rated for live load see [http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps pictures]
-*** see [http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps pictures]
 ** http://www.stageriggingonline.com/beamclamps.html
-** http://www.polarfocus.com/view.php?RBC
-*** ''level beams only''