Rope Rescue/Equipment/Need/I-beam rigging clamps

From PCSAR

< Rope Rescue | Equipment | Need(Difference between revisions)
Jump to: navigation, search
Current revision (22:09, 12 April 2011) (edit) (undo)
(Need)
 
(44 intermediate revisions not shown.)
Line 1: Line 1:
 +
== Need ==
I-beam rigging clamps
I-beam rigging clamps
* for training at Fire Hall
* for training at Fire Hall
-
** slanted I-beams 4 inches wide
+
*: [[Image:Members:Wuth-imgp1023.jpg|300px]]
-
** horizontal I-beams approx 7-8 inches wide
+
** sloped I-beams, flange 4 inches wide
-
* requirements yet to be defined
+
*** '''need to determine flange thickness'''
 +
*** exterior roof has 12 degrees slope; interior ceiling has 2 angles: the edges are greater, the center less (where we will be working)
 +
** horizontal I-beams, flange approx 7-8 inches wide
 +
*** '''need to determine flange thickness'''
 +
*** '''more accurately measure flange width'''
 +
== Requirements ==
 +
* adjustable from 4 to 8 inches
 +
* placeable on sloping I-beam up to 12 degree slope
 +
** non-rolling
 +
* MBS: 40 kN
 +
** 2 person load, SSSF, pulley at top
 +
** = 8993 lbf
 +
** WLL is not the same as MBS. It has a Design Factor (DF) built in for safety. That factor is not documented; OSHA talks about factor 2 in other parts of its standard. But without specification, we assume that the MBS is only negligibly greater than the WLL.
-
possible products:
+
== Product options ==
-
* General Clamp Industries' Universal Superclamp
+
=== Potentially suitable ===
-
** Can be Loaded at Any Angle
+
-
*** This model is designed to be used at full rated capacity at angles up to 90° in a 360° radius.
+
-
** Approved for Personnel tie-off use*
+
-
** [http://www.superclamp.com/images/ProductsImages_Universal.jpg picture]
+
-
** http://www.superclamp.com/default.asp?ID=10
+
-
** http://www.lamcoinc.com/beamclamp.html
+
-
* General Clamp Industries' Fixed-Jaw Adjustable Girder Clamp
+
* General Clamp Industries
-
** For use at up to 15° from, vertical
+
** http://www.superclamp.com/
-
** Approved for Personnel tie-off use*
+
** GCI Swivel-Jaw Adjustable Girder Clamp
-
** [http://www.superclamp.com/images/ProductsImages_Fixed.gif picture]
+
*** For use at up to 15° from horizontal
-
** http://www.superclamp.com/default.asp?ID=12
+
**** ''website says: from vertical''
 +
*** Approved for Personnel tie-off use*
 +
*** [http://www.superclamp.com/images/ProductsImages_Swivel.jpg picture]
 +
*** http://www.superclamp.com/default.asp?ID=13
 +
*** 3.5" - 12" flange
 +
**** models S6 and S6A
 +
***** WLL: 11,200 lb
 +
**** model S11
 +
***** WLL: 22,400 lb
 +
** GCI Fixed-Jaw Adjustable Girder Clamp
 +
*** For use at up to 15° from horizontal
 +
**** ''website says: from vertical''
 +
*** Approved for Personnel tie-off use*
 +
*** [http://www.superclamp.com/images/ProductsImages_Fixed.gif picture]
 +
*** http://www.superclamp.com/default.asp?ID=12
 +
*** model SX3
 +
**** WLL: 11,200 lb
 +
**** 3" - 7.5" flange
 +
***** ''might not fit larger I-beam''
-
* General Clamp Industries' Swivel-Jaw Adjustable Girder Clamp
 
-
** For use at up to 15° from vertical
 
-
** Approved for Personnel tie-off use*
 
-
** [http://www.superclamp.com/images/ProductsImages_Swivel.jpg picture]
 
-
** http://www.superclamp.com/default.asp?ID=13
 
 +
* Tractel
 +
** http://www.tractel.com/us/home.php
 +
** Corso Beam Clamp
 +
*** http://www.tractel.com/us/series.php?id_serie=73
 +
*** http://www.tractel.com/files/126564497571957.pdf
 +
*** http://www.ahsrescue.com/p-1223-pmi-tractel-beam-clamp.aspx
 +
*** http://shop.pmirope.com/technical-hardware/index.aspx?pageID=43&productID=333&productMasterID=333
 +
*** http://www.torqhoist.com/show_unique_product.php?product_id=12
 +
*** This anchorage is designed to fit I-beams from 3 to 8.25 inches. Simple installation, removable. Meets ANSI, CSA, and OSHA 5400lbs (24kN) anchorage requirements.
 +
*** Model Lt 5B
 +
**** 5 ton = 10,000 lb
 +
**** flange width: 2.9" - 8.7"
 +
*** Model Lt 10B
 +
**** 10 ton = 20,000 lb
 +
**** flange width: 3.5" - 8.7"
-
* Beam Clamp
 
-
** 3 - 9" flange widths
 
-
** WLL, Personal 2,000 lbf.
 
-
** http://www.rescuetech1.com/beamclamp.aspx
 
 +
* Reliance Fall Protection
 +
** http://www.relsafe.com/
 +
** 3093 HLL Anchor Clamp
 +
*** MBS 14,500 lb
 +
*** flange width: 4" - 16-5/8"
 +
*** horizontal or vertical I-beam
 +
*** http://www.relsafe.com/ProductDetails.aspx?guid=e8b2c0bf-5765-42c8-b21b-acf04fc19ae5&pid=561&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d2
-
* PMI Tractel Beam Clamp
+
=== suitability uncertain ===
-
** This anchorage is designed to fit I-beams from 3 to 8.25 inches. Simple installation, removable. Meets ANSI, CSA, and OSHA 5400lbs (24kN) anchorage requirements.
+
-
** one person rated.
+
-
** 24kN should be sufficient for 2 person load at rescue SSSF because not weakened by knot.
+
-
** http://www.ahsrescue.com/p-1223-pmi-tractel-beam-clamp.aspx
+
-
** http://shop.pmirope.com/technical-hardware/index.aspx?pageID=43&productID=333&productMasterID=333
+
 +
Welded ring
 +
* http://www.relsafe.com/ProductDetails.aspx?guid=11c43404-7da7-405e-a5bd-19f5737d7ccf&pid=884&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d5
-
* RELIANCE LockJaw Remote Beam Grip Clamp
 
-
** min width 5 inch
 
-
** http://www.gravitec.com/equipment/anchors/reliance-lockjaw-remote-beam-grip-clamp/anc-re-3040-1/
 
-
* FallTech 7411 Ratcheting Beam Clamp
+
=== Not suitable ===
-
** Fits Beams from 4" - 12" Wide and up to 1" Flange Thickness.
+
-
** Ideal for Horizontal I-Beam Structures.
+
-
** Rated at over 5,000 lbs .
+
-
** Meets the Requirements of OSHA 1926 and ANSI Z359.
+
-
** http://www.westernsafety.com/falltech/falltech08pg3.html
+
-
* FallTech 7485 Portable Beam Clamp
+
* rigging chains
-
** Fits Beams from 3-1/2" - 12" Wide and up to 1-1/8" Flange Thickness.
+
** ''require horizontal beam''
-
** Rated at over 5,000 lbs.
+
** http://www.polarfocus.com/view.php?RCS
-
** Meets the Requirements of OSHA 1926 and ANSI Z359.
+
-
** http://www.westernsafety.com/falltech/falltech08pg3.html
+
-
* FallTech 7486 Portable Beam Clamp
+
* All Material Handling (AMH)
-
** Fits Beams from 3-1/2" - 18" Wide and up to 1-1/8" Flange Thickness.
+
** http://www.allmaterialhandling.com/aspnet/Default.aspx
-
** Ideal for Horizontal I-Beam Structures.
+
** http://www.allmaterialhandling.com/aspnet/beamclamps.aspx
-
** Rated at over 5,000 lbs.
+
** http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps
-
** Meets OSHA and ANSI Requirements.
+
** ''not rated for live load''
-
** http://www.westernsafety.com/falltech/falltech08pg3.html
+
*** see [http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps pictures]
 +
** http://www.stageriggingonline.com/beamclamps.html
 +
** http://www.polarfocus.com/view.php?RBC
 +
*** ''level beams only''
-
* FallTech 7489 Vertical Beam Clamp
+
* FallTech
-
** Fits Beams from 2-1/2" - 12" Wide and up to 1-1/2" Flange Thickness.
+
** http://www.falltech.com/
-
** Ideal for Vertical or Horizontal I-Beam Structures.
+
** http://www.falltech.com/subCat.asp?subCatID=36
-
** Rated at over 5,000 lbs.
+
** FallTech 7489 Vertical Beam Clamp
-
** Meets OSHA and ANSI Requirements.
+
*** Fits Beams from 2-1/2" - 12" Wide and up to 1-1/2" Flange Thickness.
-
** http://www.westernsafety.com/falltech/falltech08pg3.html
+
*** Ideal for Vertical or Horizontal I-Beam Structures.
 +
*** Rated at over 5,000 lbs.
 +
*** ''no detailed strength rating''
 +
*** Meets OSHA and ANSI Requirements.
 +
*** http://www.falltech.com/productLS.asp?prodID=265
 +
*** http://www.westernsafety.com/falltech/falltech08pg3.html
 +
** FallTech 7411 Ratcheting Beam Clamp
 +
*** Fits Beams from 4" - 12" Wide and up to 1" Flange Thickness.
 +
*** Ideal for Horizontal I-Beam Structures.
 +
*** Rated at over 5,000 lbs .
 +
*** Meets the Requirements of OSHA 1926 and ANSI Z359.
 +
*** http://www.falltech.com/productLS.asp?prodID=165
 +
*** http://www.westernsafety.com/falltech/falltech08pg3.html
 +
*** ''manufacturer unclear on sloped used''
 +
** FallTech 7485 Portable Beam Clamp
 +
*** Fits Beams from 3-1/2" - 12" Wide and up to 1-1/8" Flange Thickness.
 +
*** Rated at over 5,000 lbs.
 +
*** Meets the Requirements of OSHA 1926 and ANSI Z359.
 +
*** http://www.falltech.com/productLS.asp?prodID=263
 +
*** http://www.westernsafety.com/falltech/falltech08pg3.html
 +
*** ''manufacturer unclear on sloped used''
 +
** FallTech 7486 Portable Beam Clamp
 +
*** Fits Beams from 3-1/2" - 18" Wide and up to 1-1/8" Flange Thickness.
 +
*** Ideal for Horizontal I-Beam Structures.
 +
*** Rated at over 5,000 lbs.
 +
*** Meets OSHA and ANSI Requirements.
 +
*** http://www.falltech.com/productLS.asp?prodID=264
 +
*** http://www.westernsafety.com/falltech/falltech08pg3.html
 +
*** ''manufacturer unclear on sloped used''
 +
** FallTech 7487 Stationary Beam Clamp
 +
*** Fits Beams from 4" -12" Wide and up to 1-1/8" Flange Thickness.
 +
*** Ideal for Horizontal I-Beam Structures.
 +
*** Rated at over 5,000 lbs.
 +
*** Meets the Requirements of OSHA 1926 and ANSI Z359.
 +
*** http://www.falltech.com/productLS.asp?prodID=266
 +
*** http://www.westernsafety.com/falltech/falltech08pg3.html
 +
*** ''manufacturer unclear on sloped used''
 +
** FallTech 7488
 +
*** http://www.falltech.com/productLS.asp?prodID=267
 +
*** ''wrong size''
-
* FallTech 7487 Stationary Beam Clamp
+
* General Clamp Industries
-
** Fits Beams from 4" -12" Wide and up to 1-1/8" Flange Thickness.
+
** GCI Universal Superclamp
-
** Ideal for Horizontal I-Beam Structures.
+
*** ''min flange size: 6 inch''
-
** Rated at over 5,000 lbs.
+
*** Can be Loaded at Any Angle
-
** Meets the Requirements of OSHA 1926 and ANSI Z359.
+
**** This model is designed to be used at full rated capacity at angles up to 90° in a 360° radius.
-
** http://www.westernsafety.com/falltech/falltech08pg3.html
+
*** Approved for Personnel tie-off use*
 +
*** [http://www.superclamp.com/images/ProductsImages_Universal.jpg picture]
 +
*** http://www.superclamp.com/default.asp?ID=10
 +
*** http://www.lamcoinc.com/beamclamp.html
-
Not suitable:
+
* Reliance Fall Protection
 +
** http://www.relsafe.com/
 +
** 3089 Adjustable Width Beam Anchor
 +
*** http://www.relsafe.com/ProductDetails.aspx?guid=e0d92262-7c81-4272-93ab-24e3f4b4414a&pid=907&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0
 +
*** ''MBS/WLL not specified''
 +
** 3096 Adjustable Width Sliding Beam Anchor
 +
*** http://www.relsafe.com/ProductDetails.aspx?guid=ac7bd5ec-4efd-4d1f-809b-040b9862f8fc&pid=881&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0
 +
*** flange width: 3.75" - 12.25"
 +
**** ''but manual says: 5" - 15"''
 +
*** ''maximum load: 5000lb''
 +
** 3098 Adjustable Width Beam Anchor
 +
*** 2 fall arrest links
 +
*** rated for sloped I-beams
 +
*** http://www.relsafe.com/ProductDetails.aspx?guid=afa7f5cc-699f-401d-81b3-356d5b4c3a73&pid=908&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0
 +
**** '''wrong manual on web page; cannot determine strength rating'''
 +
** LockJaw Remote Beam Grip Clamp
 +
*** ''min width 5 inch''
 +
*** rated 10,000 lb - 2 man load
 +
*** http://www.relsafe.com/ProductDetails.aspx?guid=485b7f80-88b9-46a2-8ae9-d8eeb47cf0f5&pid=555&sourceUrl=ProductsByCategory.aspx%3fcategoryId%3d100%26pg%3d0
 +
*** http://www.gravitec.com/equipment/anchors/reliance-lockjaw-remote-beam-grip-clamp/anc-re-3040-1/
-
* rigging chains (require horizontal beam)
+
* Beam Clamp (unclear manufacturer)
-
** http://www.polarfocus.com/view.php?RCS
+
** 3 - 9" flange widths
-
 
+
** WLL, Personal 2,000 lbf.
-
* http://www.polarfocus.com/view.php?RBC
+
** WLL, Equipment 4,000 lbf.
-
** "level beams only"
+
** http://www.rescuetech1.com/beamclamp.aspx
-
 
+
-
 
+
-
* possible sources:
+
-
** rating not obvious:
+
-
*** http://www.stageriggingonline.com/beamclamps.html
+
-
**** up to 3 ton readily available. Not clear whose product.
+
-
*** http://winchlines.com/merchant.mvc?Screen=CTGY&Store_Code=WINCHLINES&Category_Code=Beam_Clamps
+
-
*** http://www.torqhoist.com/show_unique_product.php?product_id=12
+

Current revision

Contents

[edit] Need

I-beam rigging clamps

  • for training at Fire Hall
    • sloped I-beams, flange 4 inches wide
      • need to determine flange thickness
      • exterior roof has 12 degrees slope; interior ceiling has 2 angles: the edges are greater, the center less (where we will be working)
    • horizontal I-beams, flange approx 7-8 inches wide
      • need to determine flange thickness
      • more accurately measure flange width

[edit] Requirements

  • adjustable from 4 to 8 inches
  • placeable on sloping I-beam up to 12 degree slope
    • non-rolling
  • MBS: 40 kN
    • 2 person load, SSSF, pulley at top
    • = 8993 lbf
    • WLL is not the same as MBS. It has a Design Factor (DF) built in for safety. That factor is not documented; OSHA talks about factor 2 in other parts of its standard. But without specification, we assume that the MBS is only negligibly greater than the WLL.

[edit] Product options

[edit] Potentially suitable



[edit] suitability uncertain

Welded ring


[edit] Not suitable