Rope Rescue/Train/PEP evaluation criteria

From PCSAR

Jump to: navigation, search


Ascending

With fixed rope already in place, either:
  • Ascend and change over to a rappel, or
  • Rappel and change over to ascending
While hanging on rope, Vertical distance covered approx. 14m, possibly sloping, vertical and/or overhanging; location dependent. Use appropriate safety procedures and proper communications terms.
Ascending done with Prusiks using one of the approved techniques.
  • Prusik
  • Change over to Rappel
  • Communications
    • Use appropriate communications prior to rappelling

Descending

  • Rappel
  • Tie-Off Descender
  • Change over to Ascend
  • Communications
    • Use appropriate communications prior to asceding

Anchor Systems

  • TL: Anchor Selection
    • Oral quiz. Using what is available on-site, describe acceptable and unacceptable anchors.
  • Simple Slung
  • Wrap 3 pull 2
  • Basket
  • 3-point System
With available trees rig a three-point anchor system using each of the three listed anchor attachments once and connect them to build an appropriate three-point load distributed anchor system.
  • Pretensioned Back-tie
Rig one anchor attachment to a tree at leas 1m above the ground, then rig pre-tensioned back-tie to tree directly behind, using 11mm rope rigged sufficiently taut.
  • Extended
With one anchor attachment in place, build extension appropriate for a 15m anchor extension.

Raising System

  • 2:1
With existing anchor, build haul system using one rope.
  • 3:1, Load Line
Build 3:1 haul system out of load line, include all appropriate Prusiks.
  • TL: Knot Pass, Load line 3:1
With previous 3:1 in place, pass knot through haul system while under simulated load.
  • 5:1, Load Line
Build 5:1 haul system from previous 3:1, inclued all appropriate Prusiks.
  • 9:1, Load Line
Build 9:1 compound haul ystem from previous 5:1, include all appropriate Prusiks.
  • Attached 3:1
Build 3:1 haul system out of a separate rope, include all appropriate Prusiks.
  • Counterbalance
Build counterbalance haul sysem out of load line, inclued all appropriate Prusiks.

Rope Management

  • Coiling
Use appropriate technique to coil rope for storage when a bag is not available.
  • Bagging
Place rope into bag including appropriate knots.
  • Care & Inspection
Demonstarte and describe care and inspection of rope, including retirement criteria.
  • Stacking
Demonstrate metho of stacking rope prior to deploying during rope rescue operations.

Patient Securement

  • TL: Secure to stretcher
Lash subject into stretcher preventing them from falling from the stretcher in any direction.

Belays

  • Tandem Prusik
Build anchor, Setup and demonstrate operation of Tandem Prusik Belay.
  • TL: Knot Pass, During L&R
Pass knot through Tandem Prusik Belay during lowering and raising
  • Munter Hitch
With anchor in place, build Munter hitch belay, demonstrate belaying a descending load, beley ascending load, catch simulated falling load, tie-off under tension, release under tension.

Ties

  • Figure 8 on-a-Bight
Tie Figure 8-on-a-bight on the end of a rope
  • Rewoven Figure 8
Tie rewoven Figure 8 knot into a closed ring
  • Figure 8 Bend
Join two ropes togethre end-to-end with figure eight bend
  • Tape Bend
Join two end of webbing together
  • Dbl. Fisherman's Bend
Joint two end of cord with double fisherman's bend
  • Clove Hitch
Tie Clove hitch into closed ring with rope, webbing or cord

Stretcher Rigging

  • Horizontal Orientation for Vertical lower/raise, 1 attendant
While wearing harness, rig stretcher in horizontal orientation for vertical raise or lower including all appropriate stretcher attendant and subject attachments, use commercial bridle for stretcher. Attach load and belay lines to MAP and make appropriate harness attachments.
  • TL: Improvised Bridle
rig above using improvised bridle in place of commercial stretcher bridle
  • Slope Rig, 3 bearers
Rig stretcher for slope raise or lower, all attachments for 3 attendants & appropropriate stretcher attachement.

Lowering Systems

  • Load Brake Rack
Properly rig brake bar rack for lowering a two-person load
  • Tie Off Brake Rack
Tie-off brake bar rack while loaded with simulated load
  • Lower with Rack
Lower a simulated load as for a two-person load
  • TL: Cover to Raise w/3:1
With simulated load, convert from a lower to rais under tension.
  • TL: Knot Pass w/RRH
With simulated load, pass a knot past the brake bar rack using the Radium Release Hitch

Edge

  • Rig Edge Person
While wearing harness set-up edge person fixed line including anch, and attach to harness.
Personal tools